banner

Home Sviluppo progetti Supporto kit ArduSiPM Mepa
Categorie Robotica / Domotica Sensori Set di sensori



Inex - Sensor Pack - 9 Sensors

Inex - Sensor Pack: 9 Sensor and Emitters (inc. Cables)
COD : RSG1009301758
Inex - Sensor Pack - 9 Sensors
0,00 € (excl. VAT)
0,00 € (incl. IVA)
Disponibilità :
not_available.gif non disponibile

This 9 Sensor Pack, provides a great set of sensors to interface with any robot, especially the Inex robots. 
All modules come with designated cables. The sensors cover a variety of possible inputs and provide a single clean connection interface

 

ZX-SWITCH - Touch sensor

• High-quality push-button switch with square knob
• If the switch is not pressed, DATA will have a logic value of "1"
• Get the supply voltage from the Master/Main microcontroller board
• Supply voltage range: +3 to +6V
• On-board LED indicator
• Inex Standard 3-pin PCB connector included
See specifications



ZX-LDR - Light Reflector Sensor 

Detects ambient light density. Works with an LDR (Light dependent resistor) or Photoresistor and allows you to have two different outputs: positive or negative DC voltage proportional to ambient light intensity.
• Works with a Photoresistor or LDR
• 2 outputs: Positive and Negative voltage reaction 
• Interface with microcontrollers and logic circuits
• Inex Standard 3-pin PCB connector

 

ZX-Tilt - Tilt Sensor

• 4-Direction Tilt Sensor
• Sharp GP1S036HEZ Sensor with built-in super compact ball for detecting tilt direction
• Active with 2-bit logic
• 2 Status LED indicators
• Detects 4 directions: 0, 90, 180 and 270 degree
• Inex Standard 3-pin PCB connector
Specifications:
• The Inex Tilt Sensor Board can detect 4 directions:
- 0° range is 330 to 360 or 0°
- 90° range is 60 to 90°
- 180° range is 150 to 180° 
- 270° range is 240 to 270°
• Suitable supply voltage: +5Vdc
• Dimensions: 41x23x12 mm

ZX-Temp - Temperature Sensor

The Inex Temperature Sensor Board works with an NTC (Negative Temperature Coefficient) thermistor. This analog sensor allows you to have two different outputs: positive or negative DC voltage proportional to ambient temperature. Its normal resistance is set to 25C.
• Detects ambient temperature
• Works with an NTC thermistor
• 2 outputs: Positive and Negative voltage reaction 
• Interface with microcontrollers and logic circuits
• Inex Standard 3-pin PCB connector

ZX-Slider - Variable Resistor Slider board

The Inex Variable Resistor Board is designed to measure distance. Two output formats available: Left or Right slide direction to increase voltage.
• Use the Inex Slide Board to measure distance
• Supply Voltage Range: +3 to +6V
• Output Voltage: 0 to +5Vcc by sliding the axis
• Interface with microcontrollers and logic circuits
• Inex Standard 3-pin PCB connector
• Compatible with all Inex controller boards

 

ZX-Photo - Infrared Photo Transistor Board

• Detects lights with a wave length of 1mm
• 2-mode operation: analog or digital
• Can detect the candle light in Fire-Fighting Robot challenges
• Use it with the Inex Infrared LED board (ZX-irLED)

Use the Inex Photo-Transistor Board in two different modes:
• Analog: The output voltage will be decreased when it detects infrared light.
• Digital: The output is logic "0" when the infrared light is detected.

 

ZX-Magnetic - Magnetic Field sensing board

The Inex Magnetic Field Sensor works with a built-in 3A Hall-effect sensor (UGN3503) which tracks extremely small changes in the magnetic flux density. This sensor provides a voltage output from 0 to +5Vdc that is proportional to the applied magnetic field. If no magnetic field is detected (0 Gauss) the output voltage will be 2.5V. The voltage output can be calculated using the formula: Vout = 2.5 + (0.0013 x Magnetic field density in Gauss units)
• Uses a 3A Hall-effect sensor (UGN3503)
• Provides a voltage output that is proportional to the applied magnetic field 
• Sensitivity: 1.3mV/Gauss
See specifications

 

ZX-LED2C - Bi-Color LED output

This one is not a sensor. The Inex Bi-Color LED Output Board is perfect to indicate the status of your robot. Two inputs are possible: HIGH with logic "1" will light the LED in Red; LOW with logic "0" will light the LED in Green. If the input signal is different, the LED will remain off.
• 3mm Bi-Color LED
• Logic "1" - LED lights Red
• Logic "0" - LED lights Green
• Interface with microcontrollers and logic circuits

 

ZX-IrLED - Infrared LED emitting Board

This one is not a sensor board. It emits Infrared light and used in conjunction with the receiver board ZX-Photo.
• A 3mm infrared LED and a current limiting resistor
• Drive with logic HIGH at TTL level
• 2-mode operation: continuous drive or frequency drive
• Transmission range is 5 to 10 meters (line of sight)
• Dimensions: 41x23x11 mm

Inex Infrared LED Board can be used in two different modes:
• Continuous Drive: In this mode, the IR-LED will receive a forward bias to drive the infrared rays. Use with the Inex Photo-transistor board for measuring the infrared light density.
• Frequency Drive: This mode will modulate a 38kHz carrier frequency into the IR-LED. (Can be used with the Inex 38kHz Infrared Receiver Module which is not included).



Pagamenti




Pagamenti con:

PayPal

Carta di credito

Bonifico bancario
anticipato

Spedizioni


24h/48h/72h

Spedizioni in tutto il mondo

con tariffe ridotte

 

Info line

 

orario continuato

dal lunedì al venerdì

10:00-18:00


(0039) 06 76971136

 

Immagini

Le informazioni riportate su robot-domestici.it
possono essere soggette a modifiche senza preavviso, alcune immagini sono a titolo indicativo.
Tutti i marchi citati sono di proprietà delle rispettive case e produttori.

Sede legale

ROBOT DOMESTICI INDUSTRIES di ARMANDO PALIANI - Via Cornelio Labeone, 76 - 00174 Roma (RM)
P.I. IT12960231004 - C.F. PLNRND74R03G763Q - REA di Roma n. RM 1413309
CODICE UNIVOCO PER LA FATTURAZIONE ELETTRONICA: KRRH6B9
Tel. (+39) 06 76971136 | e-mail: info@robot-domestici.it

Socials

facebook twitter instagram youtube pinterest