banner

Home Sviluppo progetti Supporto kit ArduSiPM Mepa
Categorie Robotica / Domotica Schede di controllo Programmabili Microschede µPanel


µPanel in Arduino USB

COD : MP-MPanelUSB
µPanel in Arduino USB
43,99 € (excl. VAT)
53,67 € (incl. IVA)
41,48 € (excl. VAT)
50,61 € (incl. IVA)

Risparmi: 3,06 €
Disponibilità :
middle.gif
5 in pronta consegna
53,67 €

 

  • SCF-TOP03

    SCF Electronics has adopted this very compact hardware (the Cactus rev.2) with the purpose to develop the TOP on the market of the stand alone Internet-Of-Things (IoT) board.
    A single board embeds a 100% Arduino compatible board along with a WiFi module. It is a landmark for the makers who want to develop low power IoT projects quickly and easily. The micro-controller unit is the Atmel ATmega32U4 while the WiFi module is based on the ESP8266. To highlight that the WiFi module firmware has been completely changed with respect the other boards in the market, we chose to name it SCF-TOP03.

    This WiFi module appears like in the following picture:

    http://www.miupanel.com/Portals/0/Website%20graphics/top03.png

    Figure 1. SCF-TOP03 Board (version derived from the Cactus board)

     

    Board pinout



    http://www.miupanel.com/Portals/0/Website%20graphics/top03_pinout.png

     

    Figure 2. Board pinout

     

    In the SCF-TOP03 board, the WiFi module pins are internally connected to the Arduino's pins as follow:


    ESP8266 Arduino
    GPIO0 12
    ENABLE (CH_PD) 13
    RX TX (Serial1)
    TX RX (Serial1)
    GND GND
    GPIO13
    GPIO12 3
    GPIO14 A4

     

    Table 1. Internal connections between Arduino and the WiFi Module

    Power Pins

    There are a variety of power and power-related nets broken out:

    • RAW is the unregulated voltage input. If the board is powered via USB, the voltage at this pin will be about 4.8V (USB’s 5V minus a schottky diode drop). On the other hand, if the board is powered externally, through this pin, the applied voltage can be up to 9V.
    • VCC is the voltage supplied to the on-board ATmega32U4. It’ll be 3.3V. This voltage is regulated by the voltage applied to the RAW pin. If the board is powered through the ‘RAW’ pin (or USB), this pin can be used as an output to supply other devices.
    • RST can be used to restart the ATmega32U4. This pin is pulled high by a 10 kOhm resistor on the board, and is active-low, so it must be connected to ground to initiate a reset. The ATmega32U4 will remain “off” until the reset line is pulled back to high.
    • GND, is the common, ground voltage (0V reference) for the system.

    I/O Pins

    The board’s I/O pins – 18 in all – are multi-talented. Every pin can be used as a digital input or output, for blinking LEDs or reading button presses. These pins are referenced in the Arduino IDE via an integer value between 0 and 21. (The A0-A3 pins can be referenced digitally using either their analog or digital pin number).

    Nine pins feature analog to digital converters (ADCs) and can be used as analog inputs. These are useful for reading potentiometers or other analog devices using the analogRead([pin]) function.

    There are five pins with pulse width modulation (PWM) functionality, which can be used as analog output using the analogWrite([pin], [value]) function. These pins are indicated on-board with a faint, white circle around them.

    There are hardware UART (serial), I2C, and SPI pins available as well. These can be used to interface with digital devices like serial LCDs, XBees, IMUs, and other serial sensors.

    The board has five external interrupts, which allow you to instantly trigger a function when a pin goes either high or low (or both). If you attach an interrupt to an interrupt-enabled pin, you’ll need to know the specific interrupt to pin map: pin 3 maps to interrupt 0, pin 2 is interrupt 1, pin 0 is interrupt 2, pin 1 is interrupt 3, and pin 7 is interrupt 4.

    How to Power the board

    Since the main feature is its innate USB functionality, the most common way to power it is via USB. In this setup, the board will regulate to 3.3V the 5V supply coming in from the USB. The other end of the USB cable can be connected to either a computer, USB hub, or a USB wall adapter, which can (in most cases) provide more power.

    Alternatively, if your board is living out in the wild, it can be powered through either the ‘RAW’ or ‘VCC’ pins. A supply going into the ‘RAW’ pin will be regulated down to the correct operating voltage (3.3V). To be safe, it shouldn’t be any higher than 9V, and it should be at least 1V more than the regulated voltage (e.g. > 4.3V).

    If you power the board through the ‘VCC’ pin, keep in mind that this signal is unregulated. Only use this if you have a clean, regulated 3.3V supply to connect to it.

     

    Operating mode of the onboard WiFi Module

     

     

    After power-up (or reset) the on-board WiFi module can boot in two different modes, depending on the logic levels applied on its pins GPIO0 and GPIO2. Since these pins are internally routed to the Arduino side (as reported in table 1), in your Arduino sketch you have to take care to correctly set these pins on reset (see the sketch example below).

    1. Firmware RUN mode:

    • GPIO0 = '1'
    • GPIO2 = '1' (on the SCF-TOP03 is internally forced to Vcc)
    • TX = '1' (Important: make sure your micro-controller keeps the TX line high during the module boot)

    2. Programming Mode (*)

    • GPIO0 = '0'
    • GPIO2 = '1'

    (*) IMPORTANT: to correctly update the module's µPanel firmware, do NOT use this solution, otherwise you will lose definitely the µPanel firmware! The correct way is launch the update request from µPanel APP, from the module configuration menu.

     

    Arduino Sketch Example

    IMPORTANT: before loading your sketch, please select the board "LilyPad Arduino USB" in the boards menu.
    If you have accidentally selected another board, and already tried loading your sketch, read here:

    www.arduino.cc/en/Guide/ArduinoLilyPadUSB

    This board (like Lilypad USB and Leonardo) use "Serial1" to communicate with on-board the WiFi module via TTL serial on pins 0 (RX) and 1 (TX).  "Serial" is reserved for USB CDC communication.

     

    /**************************************************
     
     --- IMPORTANT ---: before to load your sketch, please select the board "LilyPad Arduino USB" in the boards menu.
     If you have accidentally select another board, and load your sketch, read here:
     www.arduino.cc/en/Guide/ArduinoLilyPadUSB
      
     Connection table:
     
     * ESP8266  Arduino
     * GPIO0    12
     * ENABLE   13
     * RX       TX
     * TX       RX
     * GND      GND
     
    
     About Serial
     The "Lilypad USB" (and the board derived from it) use "Serial1" to communicate via TTL serial on pins 0 (RX) and 1 (TX). 
     "Serial" is reserved for USB CDC communication.
    
     ***************************************************/
    
    
    #define ESP_PROGRAM_PIN  12
    #define ESP_ENABLE_PIN  13
    
    
    void setup() {
    
      Serial1.begin(57600);        // Initialise serial 1 (WiFi Module)
          
      pinMode(ESP_ENABLE_PIN, OUTPUT);
      pinMode(ESP_PROGRAM_PIN, OUTPUT);
      
      // Set ESP module in RUN mode on reset 
      digitalWrite(ESP_PROGRAM_PIN, HIGH);  
      digitalWrite(ESP_ENABLE_PIN, HIGH);
    
      delay(5000);                 // Let's the module start
      
      // Discharge old partial messages
      Serial1.println("");
      
      // Enable real-time response
    }


Forse potresti essere interessato a questo(i) prodotto(i)


20,61 € (excl. VAT)
25,14 € (incl. IVA)
19,24 € (excl. VAT)
23,47 € (incl. IVA)

Risparmi: 1,67 €
21,30 € (excl. VAT)
25,99 € (incl. IVA)

Pagamenti




Pagamenti con:

PayPal

Carta di credito

Bonifico bancario
anticipato

Spedizioni


24h/48h/72h

Spedizioni in tutto il mondo

con tariffe ridotte

 

Info line

 

orario continuato

dal lunedì al venerdì

10:00-18:00


(0039) 06 76971136

 

Immagini

Le informazioni riportate su robot-domestici.it
possono essere soggette a modifiche senza preavviso, alcune immagini sono a titolo indicativo.
Tutti i marchi citati sono di proprietà delle rispettive case e produttori.

Sede legale

ROBOT DOMESTICI INDUSTRIES di ARMANDO PALIANI - Via Cornelio Labeone, 76 - 00174 Roma (RM)
P.I. IT12960231004 - C.F. PLNRND74R03G763Q - REA di Roma n. RM 1413309
CODICE UNIVOCO PER LA FATTURAZIONE ELETTRONICA: KRRH6B9
Tel. (+39) 06 76971136 | e-mail: info@robot-domestici.it

Socials

facebook twitter instagram youtube pinterest