Overview
The D24V150Fx family of step-down voltage regulators are high-current synchronous switching regulators that generate lower output voltages from input voltages as high as 40V. These types of regulators are also known as switched-mode power supplies (SMPS) or DC-to-DC converters, and they are much more efficient than linear voltage regulators, especially when the difference between the input and output voltage is large. In particular, the D24V150Fx family of regulators have typical efficiencies of 80% to 95%, depending on factors like input voltage, output voltage, and load.
These regulators have an instantaneous current limit of approximately 32A, but they are limited in the long term to much lower currents by power dissipation and the corresponding temperature rise that induces in the board. The regulators can typically support continuous output currents between 5A and 20A without additional cooling (such as with a heat sink or forced airflow), depending on the input voltage and output voltage. In general, the available output current is a little higher for the lower-voltage versions than it is for the higher-voltage versions, and it decreases as the input voltage increases. See the Typical efficiency and output current section at the bottom of this page for more details.
These regulators have a typical quiescent (no load) current draw of around 100mA, and an enable pin can be used to put the boards in a low-power state that reduces the quiescent current to approximately 5µA to 10µA per volt on VIN.
During normal operation, this product can get hot enough to burn you. Even with very light loads, the regulator can run very hot if the input voltage is high, and the higher the input voltage the hotter the regulator will run. Take care when handling this product or other components connected to it.
The modules have built-in reverse-voltage protection, short-circuit protection, a thermal shutdown feature that helps prevent damage from overheating, and a soft-start feature that reduces inrush current. They also feature undervoltage lockout that disables the regulator if the input voltage falls below about 3.5V.
Several different fixed output voltages are available:
The different voltage versions of this regulator all look very similar, so you should consider adding your own distinguishing marks or labels if you will be working simultaneously with multiple versions. A white box is provided on the bottom silkscreen of the regulator to make labeling easier. This product page applies to all versions of the D24V150Fx family.
Features
- Input voltage:
- 4.5V to 40V for the version that outputs 3.3V
- [outputvoltage+dropoutvoltage] to 40V for output voltages of 5V and higher (see below for more information on dropout voltage)
- Fixed 3.3V, 5V, 6V, 7.5V, 9V, or 12V output (depending on regulator version) with 4% accuracy
- Typical maximum continuous output current between 5A and 20A
- Typical efficiency of 80% to 95%, depending on input voltage, output voltage, and load
- Integrated reverse-voltage protection, over-current protection, over-temperature shutoff, undervoltage lockout, and soft-start
- Typical no-load quiescent current of 100mA ; this can be reduced to approximately 5µA to 10µA per volt on VIN by disabling the board
- #8220;Power good#8221; output indicates when the regulator cannot adequately maintain the output voltage
- Compact size: 1.7³times;1.25³times;0.43³ (43.2mm times; 31.8mm times; 11mm)
- Four 0.086³ mounting holes for #2 or M2 screws
Using the regulator
Connections
These buck regulators have six connections: input voltage (VIN), output voltage (VOUT), enable (EN), power good (PG), mode (MOD), and ground (GND).
The input voltage, VIN, powers the regulator. Voltages between 4.5V and 40V can be applied to VIN, but for versions of the regulator that have an output voltage higher than 4.5V, the effective lower limit of VIN is VOUT plus the regulator#8217;s dropout voltage, which varies approximately linearly with the load (see below for a graph of dropout voltages as a function of the load).
The output voltage, VOUT, is fixed and depends on the regulator version: the D24V150F3 version outputs 3.3V, the D24V150F5 version outputs 5V, the D24V150F6 version outputs 6V, the D24V150F7 version outputs 7.5V, the D24V150F9 version outputs 9V, and the D24V150F12 version outputs 12V.
The regulator#8217;s enable input, EN, is pulled high (to 5V) internally, which enables the regulator by default. The EN pin can be driven low (under 1V) to disable the output and put the board into a low-power state. The quiescent current draw in this sleep mode is dominated by the current in an internal pull-up resistor and the reverse-voltage protection circuit, which altogether will draw between 5micro;A and 10micro;A per volt on VIN when EN is held low. To bring the board out of this low-power state, the EN pin should be pulled above 2V. If you do not need this feature, you can leave the EN pin disconnected.
The #8220;power good#8221; indicator, PG, is an open-drain output that goes low when the regulator#8217;s output falls below around 85% of the nominal voltage, including when the enable pin is held low, or rises above around 115% of the nominal voltage. Otherwise, the PG pin is high-impedance, so an external pull-up resistor is required to use this pin.
The mode input, MOD, is pulled low internally, which selects fixed-frequency operation by default. This pin can be driven high (above 2V, but not exceeding 5V) to override fixed-frequency operation to reduce quiescent current (and therefore to increase efficiency) at light loads (on the order of a few milliamps). This reduced-power feature is available when the input voltage is substantially higher than the output voltage (see the item-specific details section at the bottom of this page for more information).
|
Pololu Step-Down Voltage Regulator D24V150Fx with included hardware. |
---|
The connections are labeled on the back side of the PCB, and the board offers several options for making electrical connections. The three sets of smaller through-holes are arranged with a 0.1³ spacing for compatibility with solderless breadboards, connectors, and other prototyping arrangements that use a 0.1³ grid; you can solder pieces of the included 13—1 straight male header strip into these smaller holes. Alternatively, you can solder the included 2-pin 5mm-pitch terminal blocks to the two pairs of larger holes. For the most compact installation, you can solder wires directly to the board.
| Pololu Step-Down Voltage Regulator D24V150Fx in a breadboard, assembled with terminal blocks and male headers. |
---|
|
| Pololu Step-Down Voltage Regulator D24V150Fx showing wires soldered directly to the board. |
---|
|
The board has four 0.086³ mounting holes intended for #2 or M2 screws. The mounting holes are in the four corners of the board and are separated by 1.53³ horizontally and 1³ vertically. For all the board dimensions, see the dimension diagram (307k pdf).
Typical efficiency and output current
The efficiency of a voltage regulator, defined as (Powerout)/(Powerin), is an important measure of its performance, especially when battery life or heat are concerns. This family of switching regulators typically has an efficiency of 80% to 95%, though the actual efficiency in a given system depends on input voltage, output voltage, and output current. See the efficiency graph near the bottom of this page for more information.
The maximum achievable continuous output current is typically between 5A and 20A, but this depends on many factors, including the ambient temperature, air flow, heat sinking, and the input and output voltage. See the continuous output current graph near the bottom of this page for more information. The maximum instantaneous current is limited to approximately 32A.
Typical dropout voltage
The dropout voltage of a step-down regulator is the minimum amount by which the input voltage must exceed the regulator#8217;s target output voltage in order to ensure the target output can be achieved. For example, if a 5V regulator has a 1V dropout voltage, the input must be at least 6V to ensure the output is the full 5V. Generally speaking, the dropout voltage increases as the output current increases. See the #8220;Details#8221; section below for more information on the dropout voltage for this specific regulator version.
Details for item #2882
| Pololu 6V, 15A Step-Down Voltage Regulator D24V150F6, top view. |
---|
|
| Pololu 6V, 15A Step-Down Voltage Regulator D24V150F6, bottom view. |
---|
|
The graphs below show the typical efficiency, maximum continuous current, and dropout voltage of the 6V D24V150F6 regulator:
Power-save mode for the 6V version
For this 6V regulator version, the power-save mode is available for input voltages above 18V. See the Connections section above for details on the MOD pin, which is used to activate this mode.