CH551G Development board

Features

• Complete development board in a pocket-size with SOP16 package
• Rich I/O interfaces for project expandability
• 4 channel capacitive touch buttons for touch applications
• Support USB 2.0 full speed 12mbps or low speed 1.5mbps with direct download
• Compatible with breadboard via the header with 2.54mm pin spacing

Description

CH551G development board features the CH551 chip, which is an enhanced e8051 core single-chip microcomputer compatible with MCS51 instruction set. 79% of its instructions are single-byte single-cycle instructions, and the average instruction speed is 8-15 times faster than the standard MCS51.

Ch551 supports up to 24MHz system main frequency. It has built-in 10KB program memory (ROM), 256-byte internal IRAM, and 512 bytes on-chip xram. Xram supports DMA (direct memory access).

The ch551 has 4 channel capacitive touch buttons, three sets of timers and signal capture, PWM, SPI, asynchronous serial port (UART0), USB device controller, and full speed transceiver.

Specifications

• Core: enhanced e8051 core, compatible with MCS51 instruction set. 79% of its instructions are single byte single cycle instructions. The average instruction speed is 8-15 times faster than the standard MCS51. It has a special xram data replication instruction and double dptr pointer.
• ROM: 10 KB capacity of multi programmable non-volatile memory ROM, can be used for all program storage space
• Data Flash: 128 bytes multi erasable non-volatile data memory, which supports rewriting data in bytes.
• RAM: 256 bytes internal RAM, which can be used for fast data storage and stack; 512 bytes on chip xram can be used for large amount of data temporary storage and DMA (direct memory access).
• USB: embedded USB controller and USB transceiver, supporting USB device mode, master-slave detection, supporting USB 2.0 full speed 12mbps or low-speed 1.5mbps. FIFO is built-in and supports 64 bytes of data packets.
• Timer: three groups of timers, t0 / T1 / T2 is the standard MCS51 timer.
• Capture: timer T2 is extended to support 2-way signal capture.
• PWM: 2 sets of PWM output, pwm1 / pwm2 is 2-way 8-bit PWM output.
• UART: asynchronous serial port, support higher communication baud rate, UART0 is the standard MCS51 serial port.
• SPI: SPI controller has built-in FIFO, clock frequency up to half of the system s main frequency Fsys, supports serial data input and output simplex multiplexing, and supports master / slave mode.
• Touch key: 4-channel capacitance detection, support independent timing interrupt.
• GPIO: supports up to 17 GPIO pins (including Xi / XO, RST and USB signal pins).
• Interrupt: supports 14 groups of interrupt signal sources, including 6 groups of interrupts (INT0, T0, INT1, T1, etc.) compatible with standard MCS51 UART0, T2), and extended 8 groups of interrupts (spi0, tkey, USB, ADC, uart1, pwmx, GPIO, wdog), in which GPIO interrupt can be selected from 7 pins.
• Watch dog: 8 bits can preset watchdog timer wdog, support timing interrupt.
• Reset: support 4 kinds of reset signal source, built-in power on reset, support software reset and watchdog overflow reset, optional pin external input reset.
• Clock: built in 24 MHz clock source, which can support external crystal by multiplexing GPIO pins.
• Power: built in 5V to 3.3V low voltage differential voltage regulator, supporting 5V or 3.3V or even 2.8V power supply voltage. It supports low-power sleep, USB, UART0, uart1, spi0 and part of GPIO external wake-up.
• The chip has a unique ID number.

Hardware Overview

Part List 

1 x CH551G Development board