banner

Utente dimenticato? Password dimenticata? Registrati
Categorie Prodotti al prezzo di costo 3D-Printing 3D Electronics



PrintHat v1 - 32-bit motor controller board for Raspberry Pi

COD : RR-WLPRINTHAT
PrintHat v1 - 32-bit motor controller board for Raspberry Pi
75,12 € (excl. VAT)
91,65 € (incl. IVA)
Disponibilità :
yellow.gif spedito in 3-7 giorni

quantità disponibile: 9999

The WreckLab PrintHAT is a high performance controller board for the Raspberry Pi and currently the only such board on the market specifically designed around the increasingly recognized firmware called "Klipper", the new kid-on-the-block in the 3D printing community. In simple terms: Klipper s architecture is designed to distribute the computational overhead for high speed, high resolution motor steps to a powerful microcomputer (e.g. Raspberry Pi), freeing up the controller board to execute those steps with greater smoothness and precision.

The PrintHAT is directed primarily at printing enthusiasts and small businesses who are looking into (or already using) OctoPrint as one of their primary 3D printer controller interfaces, since Klipper (and PrintHAT by extension) have been extensively built around OctoPrint s well established and highly developed GUI. While the PrintHAT & Raspberry Pi work behind the scenes, Octoprint provides the user with an advanced, flexible and highly extensible Human-to-Machine controller interface, which now include integrated options for automated processes (macros), event-driven interrupts (filament runout sensors) and web cameras.

Transitioning from other controllers and firmwares? No problem! The PrintHAT comes with a dummy-proof installer package that makes installation a breeze for busy beginners, while also being customizable to the requirements of more experienced users. Whether you are in the market for a new machine or wish to upgrade your current configuration, the PrintHAt + Raspberry Pi configuration packs features, power and convenience in a small, clean form factor with minimum hassle and plenty of documentation.

NOTE: A Raspberry Pi is required to operate the printHAT and must be obtained separately. PrintHAT is compatible with Raspberry Pi v0/1/2/3, but the best performance is obtained with v2 & 3.

Specifications:

  •     Powerful 32 Bit ARM Cortex processor (TM32F103)
  •     9-26V input voltage
  •     4x TMC2130 stepper drivers
  •     Enhanced endstop accuracy with the stepper phase detection smart correction
  •     Sensorless homing
  •     StealthChop supported for extremely quiet operation and smooth motion
  •     Up to 256 microsteps per full step
  •     4x PWM output (up to 10A per channel)
  •     8x GPIOs fully configurable (endstops, filament sensor, etc)
  •     2x ADC input

Package contents:

  • 1x printHAT board
  • 1x boot jumper
  • 1x 2x2 pin header
  • 3x Molex 395100002
  • 1x Mounting Kit (2x M2.5x11 hex spacers,4x M2.5x5 Phillips screws)

Pagamenti




Pagamenti con:

PayPal

Carta di credito

Bonifico bancario
anticipato

Spedizioni


24h/48h/72h

Spedizioni in tutto il mondo

con tariffe ridotte

 

Info line

 

orario continuato

dal lunedì al venerdì

10:00-18:00


(0039) 06 76971136

 

Immagini

Le informazioni riportate su robot-domestici.it
possono essere soggette a modifiche senza preavviso, alcune immagini sono a titolo indicativo.
Tutti i marchi citati sono di proprietà delle rispettive case e produttori.

Sede legale

ROBOT DOMESTICI INDUSTRIES di ARMANDO PALIANI - Via Cornelio Labeone, 76 - 00174 Roma (RM)
P.I. IT12960231004 - C.F. PLNRND74R03G763Q - REA di Roma n. RM 1413309
CODICE UNIVOCO PER LA FATTURAZIONE ELETTRONICA: KRRH6B9
Telefono 06 76971136